Skip to content

Fischer Panda

Knowledge Base

  • Event Codes
    • Event Codes
    • iControl2 error codes
    • Inverter blink codes
  • fpControl View
  • fpControl
    • Application Notes fpC
    • Technical Datasheets fpC
    • Generator type codes
  • iControl2
    • Application Notes iC2
    • Technical Datasheets iC2
  • Inverter
    • Application Notes Inverter
    • Technical Datasheets Inverter
  • Communication
    • SAE J1939
    • NMEA 2000®
    • Victron GX
    • Multifunction Displays
  • System
  • Glossary
  • Service

Category Archives: Inverter

Inverter blink codes

This article explains the blink codes of the status LEDs of Fischer Panda PMGi inverters.

Posted byFischer PandaNovember 13, 2020November 17, 2020Posted inApplication Notes Inverter, Inverter

Datasheet IGBT driver board »FP1601«

Application The »FP1601« is a driver board for external IGBT modules. The IGBT driver board is used combined with the Inverter control board »FP1602« in Fischer Panda inverter synchronous generators with 1-phase and 3-phase inverters with an output of more than 10 kVA. Product description The IGBT driver board can drive IGBT modules up to […]

Posted byFischer PandaOctober 23, 2020October 30, 2020Posted inInverter, Technical Datasheets Inverter

Datasheet Inverter control board »FP1602«

The Inverter control board »FP1602« is a printed circuit board for use in Fischer Panda inverter synchronous generators with 1-phase and 3-phase inverters with an output of more than 25 kVA.

Posted byFischer PandaOctober 19, 2020October 30, 2020Posted inInverter, Technical Datasheets Inverter

Datasheet Inverter control board »FP1503«

The Inverter control board »FP1503« is a printed circuit board for use in Fischer Panda inverter synchronous generators with 1-phase and 3-phase inverters up to 25 kVA.

Posted byFischer PandaOctober 9, 2020October 30, 2020Posted inInverter, Technical Datasheets Inverter

Datasheet Inverter control board »P12000«

The Inverter control board »P12000« is a printed circuit board for use in Fischer Panda inverter synchronous generators with 1-phase inverters up to 25 kVA.

Posted byFischer PandaOctober 7, 2020October 30, 2020Posted inInverter, Technical Datasheets Inverter

Inverter softstart with fpControl

You can use the additional start function “inverter softstart” to avoid problems when starting large electrical loads. If this function is activated, the inverter carries out measures at start-up to limit the power when switching on the loads (softstart).

Posted byFischer PandaDecember 6, 2019October 30, 2020Posted inApplication Notes Inverter, Inverter

fpControl – Start without inverter

In order to check whether the inverter causes a fault, it is often a first test to start the generator without an inverter. The function “Start without inverter” (start w/o inverter) is an additional start function for this use case. It simulates the engine revolution so that the generator can be started without inverter in case of service.

Posted byFischer PandaDecember 5, 2019October 30, 2020Posted inApplication Notes Inverter, Inverter

Event 167 – No rotation monitoring / evaluation

Simulation of the engine speed so that the generator can be started without inverter in case of service.

Posted byFischer PandaJune 14, 2019October 30, 2020Posted inEvent Codes, Inverter

Event 38 – Output Inverter DC supply low

The current at the output for the DC supply voltage of the inverter is below its lower limit.

Posted byFischer PandaJune 14, 2019October 30, 2020Posted inEvent Codes, Inverter

News

  • Event 172 – Synchronization Module offline December 18, 2020
  • Event 171 – Load Contactor switched off forced December 18, 2020
  • Start repetitions in automatic start mode November 26, 2020
  • Inverter blink codes November 13, 2020
  • Parallel connection of two asynchronous generators November 10, 2020

Categories

  • AGT
  • Application Notes fpC
  • Application Notes Inverter
  • Communication
  • Event Codes
  • fpControl
  • iControl2
  • Inverter
  • Multifunction Displays
  • NMEA 2000®
  • SAE J1939
  • Software Update
  • System
  • Technical Datasheets fpC
  • Technical Datasheets iC2
  • Technical Datasheets Inverter
  • Victron GX

Archive

  • December 2020
  • November 2020
  • October 2020
  • September 2020
  • August 2020
  • July 2020
  • June 2020
  • May 2020
  • April 2020
  • January 2020
  • December 2019
  • November 2019
  • October 2019
  • September 2019
  • July 2019
  • June 2019
  • May 2019
  • April 2019

Search …

Fischer Panda, Proudly powered by WordPress. Data Protection Policy
  • Site Terms & Conditions (Impressum)
  • Home
  • Glossary
  • Service