Skip to content

Fischer Panda

Knowledge Base

  • Event Codes
    • Event Codes
    • iControl2 error codes
    • Inverter blink codes
  • fpControl View
  • fpControl
    • Application Notes fpC
    • Technical Datasheets fpC
    • Generator type codes
  • iControl2
    • Application Notes iC2
    • Technical Datasheets iC2
  • Inverter
    • Application Notes Inverter
    • Technical Datasheets Inverter
  • Communication
    • SAE J1939
    • NMEA 2000®
    • Victron GX
    • Multifunction Displays
  • System
  • Glossary
  • Service

Category Archives: Event Codes

Event 173 – BMS lost

The CAN communication with the BMS has been lost.

Posted byFischer PandaJanuary 18, 2021January 18, 2021Posted inEvent Codes

Event 172 – Synchronization Module offline

The Synchronization Module is offline while the Generator Control is in »parallel mode«.

Posted byFischer PandaDecember 18, 2020December 18, 2020Posted inEvent Codes

Event 171 – Load Contactor switched off forced

The Load Contactor has been switched off forced.

Posted byFischer PandaDecember 18, 2020December 18, 2020Posted inEvent Codes

Event 168 – Bus #1 dead

No communication on the respective other side when using sync-module.

Posted byFischer PandaAugust 27, 2020January 18, 2021Posted inEvent Codes

Event 169 – Start Request Denied

Start request denied.

Posted byFischer PandaAugust 27, 2020October 30, 2020Posted inEvent Codes

Event 170 – Remote Start Request Denied

Remote start request denied.

Posted byFischer PandaAugust 27, 2020October 30, 2020Posted inEvent Codes

Event 62 – Temperature fuel low

The temperature of the fuel is below its lower limit.

Posted byFischer PandaNovember 5, 2019October 30, 2020Posted inEvent Codes

Event 10 – Temperature exhaust low

The temperature of the exhaust is below its lower limit.

Posted byFischer PandaNovember 4, 2019October 30, 2020Posted inEvent Codes

Event 9 – Temperature winding low

The temperature of the winding is below its lower limit.

Posted byFischer PandaNovember 4, 2019October 30, 2020Posted inEvent Codes

Event 8 – Temperature engine low

The temperature of the engine is below its lower limit

Posted byFischer PandaNovember 4, 2019October 30, 2020Posted inEvent Codes

Posts navigation

1 2 3 … 12 Older posts

News

  • Event 173 – BMS lost January 18, 2021
  • Event 172 – Synchronization Module offline December 18, 2020
  • Event 171 – Load Contactor switched off forced December 18, 2020
  • Start repetitions in automatic start mode November 26, 2020
  • Inverter blink codes November 13, 2020

Categories

  • AGT
  • Application Notes fpC
  • Application Notes Inverter
  • Communication
  • Event Codes
  • fpControl
  • iControl2
  • Inverter
  • Multifunction Displays
  • NMEA 2000®
  • SAE J1939
  • Software Update
  • System
  • Technical Datasheets fpC
  • Technical Datasheets iC2
  • Technical Datasheets Inverter
  • Victron GX

Archive

  • January 2021
  • December 2020
  • November 2020
  • October 2020
  • September 2020
  • August 2020
  • July 2020
  • June 2020
  • May 2020
  • April 2020
  • January 2020
  • December 2019
  • November 2019
  • October 2019
  • September 2019
  • July 2019
  • June 2019
  • May 2019
  • April 2019

Search …

Fischer Panda, Proudly powered by WordPress. Data Protection Policy
  • Site Terms & Conditions (Impressum)
  • Home
  • Glossary
  • Service