{"id":7956,"date":"2024-08-02T10:21:31","date_gmt":"2024-08-02T08:21:31","guid":{"rendered":"https:\/\/knowledgebase.fischerpanda.de\/?p=7956"},"modified":"2025-09-15T12:11:15","modified_gmt":"2025-09-15T10:11:15","slug":"fpcontrol-setting-servo-motor-on-vs-generators","status":"publish","type":"knowledgebase","link":"https:\/\/knowledgebase.fischerpanda.de\/?knowledgebase=fpcontrol-setting-servo-motor-on-vs-generators","title":{"rendered":"VS Generator System\u00a0\u2013\u00a0Setting Servo Motor on VS Generators"},"content":{"rendered":"\n<h3 class=\"wp-block-heading h3-weiss-blau\">Introduction to the topic<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">You can adjust the minimum and maximum position of the servo motor on Fischer Panda VS generators with fpControl generator control and Kubota V1505 engine. This is necessary, for example, when starting up for the first time and after changing a defective servo motor or a defective fpControl generator control.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><tbody><tr><td><img decoding=\"async\" width=\"56\" height=\"56\" class=\"wp-image-2536\" style=\"width: 56px;\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2019\/10\/information_sbu_transparent_52px.png\" alt=\"\"><\/td><\/tr><tr><td>This manual can only be used for VS generators with Kubota V1505 engine, e. g. the VS 20. <br><strong>NOTE: The VS 45 is controlled by the Hatz engine. No settings need to be made here.<\/strong><\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h3 class=\"wp-block-heading h3-weiss-blau\">Setting the minimum position<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Check the set generator type. Adjust the type if necessary. See a list of generator types <a aria-label=\"here (opens in a new tab)\" href=\"https:\/\/knowledgebase.fischerpanda.de\/?knowledgebase=generator-type-codes\" target=\"_blank\" rel=\"noreferrer noopener\">here<\/a>.<\/li>\n\n\n\n<li>Switch off the generator control.<\/li>\n\n\n\n<li>Mount the servo throttle lever on the servo motor so that the lever is horizontal (Fig. 1).  <\/li>\n<\/ul>\n\n\n<div class=\"wp-block-image is-resized\">\n<figure class=\"aligncenter size-full\"><img decoding=\"async\" width=\"3679\" height=\"2065\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_1_min-pos_2.3_1.jpg\" alt=\"\" class=\"wp-image-5750\" srcset=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_1_min-pos_2.3_1.jpg 3679w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_1_min-pos_2.3_1-300x168.jpg 300w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_1_min-pos_2.3_1-768x431.jpg 768w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_1_min-pos_2.3_1-1024x575.jpg 1024w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_1_min-pos_2.3_1-1568x880.jpg 1568w\" sizes=\"(max-width: 3679px) 100vw, 3679px\" \/><figcaption class=\"wp-element-caption\"> <em>Fig. 1: Servo throttle mounted in horizontal position <\/em><\/figcaption><\/figure>\n<\/div>\n\n\n<ul class=\"wp-block-list\">\n<li>Switch on the generator control. The servo throttle lever should now be in the approximately 4 o&#8217;clock position (Fig. 2).  <\/li>\n<\/ul>\n\n\n<div class=\"wp-block-image is-resized\">\n<figure class=\"aligncenter\"><img decoding=\"async\" width=\"948\" height=\"712\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_servo_gashebel_4Uhr_Pos_small.jpg\" alt=\"\" class=\"wp-image-5752\" srcset=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_servo_gashebel_4Uhr_Pos_small.jpg 948w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_servo_gashebel_4Uhr_Pos_small-300x225.jpg 300w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_servo_gashebel_4Uhr_Pos_small-768x577.jpg 768w\" sizes=\"(max-width: 948px) 100vw, 948px\" \/><figcaption class=\"wp-element-caption\"><em>Fig. 2: Servo throttle lever in 4 o&#8217;clock position<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n<ul class=\"wp-block-list\">\n<li>Adjust the position of the engine throttle lever with the left nut (Fig. 3) so that there remains an air gap between the engine throttle lever and the stop lever (Fig. 4).  <\/li>\n<\/ul>\n\n\n<div class=\"wp-block-image is-resized\">\n<figure class=\"aligncenter\"><img decoding=\"async\" width=\"1024\" height=\"745\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_4_max-pos_schraube_1-1024x745.jpg\" alt=\"\" class=\"wp-image-5755\" srcset=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_4_max-pos_schraube_1-1024x745.jpg 1024w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_4_max-pos_schraube_1-300x218.jpg 300w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_4_max-pos_schraube_1-768x559.jpg 768w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_4_max-pos_schraube_1-1568x1141.jpg 1568w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><figcaption class=\"wp-element-caption\"> <em>Fig. 3: Adjusting the position of the engine throttle lever with the left nut<\/em><\/figcaption><\/figure>\n<\/div>\n\n<div class=\"wp-block-image is-resized\">\n<figure class=\"aligncenter\"><img decoding=\"async\" width=\"1024\" height=\"576\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_2_min-pos_anschlag_2-1024x576.jpg\" alt=\"\" class=\"wp-image-5756\" srcset=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_2_min-pos_anschlag_2-1024x576.jpg 1024w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_2_min-pos_anschlag_2-300x169.jpg 300w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_2_min-pos_anschlag_2-768x432.jpg 768w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_2_min-pos_anschlag_2-1568x882.jpg 1568w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_2_min-pos_anschlag_2.jpg 2000w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><figcaption class=\"wp-element-caption\"><em> Fig. 4: Minimum position &#8211; air gap between engine throttle lever and stop lever<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n<ul class=\"wp-block-list\">\n<li>Turn the right nut to the left as far as possible (Fig. 5) so that the engine throttle lever has no more clearance (Fig. 6).  <\/li>\n<\/ul>\n\n\n<div class=\"wp-block-image is-resized\">\n<figure class=\"aligncenter\"><img decoding=\"async\" width=\"948\" height=\"571\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_rechte_mutter_small.jpg\" alt=\"\" class=\"wp-image-5758\" srcset=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_rechte_mutter_small.jpg 948w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_rechte_mutter_small-300x181.jpg 300w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_rechte_mutter_small-768x463.jpg 768w\" sizes=\"(max-width: 948px) 100vw, 948px\" \/><figcaption class=\"wp-element-caption\"><em>Fig. 5: Turn the right nut left to the stop<\/em><\/figcaption><\/figure>\n<\/div>\n\n<div class=\"wp-block-image is-resized\">\n<figure class=\"aligncenter\"><img decoding=\"async\" width=\"948\" height=\"712\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_rechte_mutter_anschlag_small.jpg\" alt=\"\" class=\"wp-image-5760\" srcset=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_rechte_mutter_anschlag_small.jpg 948w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_rechte_mutter_anschlag_small-300x225.jpg 300w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_rechte_mutter_anschlag_small-768x577.jpg 768w\" sizes=\"(max-width: 948px) 100vw, 948px\" \/><figcaption class=\"wp-element-caption\"> <em>Fig. 6: No clearance between the right nut and the engine throttle<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n<hr class=\"wp-block-separator has-css-opacity is-style-dots\"\/>\n\n\n\n<h3 class=\"wp-block-heading h3-weiss-blau\">Setting the maximum position<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>After setting the maximum position, verify that in the <strong>full throttle position<\/strong> there is only an air gap between the <strong>engine throttle lever<\/strong> and the <strong>limit screw<\/strong> (Fig. 7).  <\/li>\n<\/ul>\n\n\n<div class=\"wp-block-image is-resized\">\n<figure class=\"aligncenter size-large\"><img decoding=\"async\" width=\"1024\" height=\"745\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_5_max-pos_anschlag_1-1024x745.jpg\" alt=\"\" class=\"wp-image-5766\" srcset=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_5_max-pos_anschlag_1-1024x745.jpg 1024w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_5_max-pos_anschlag_1-300x218.jpg 300w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_5_max-pos_anschlag_1-768x558.jpg 768w, https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_5_max-pos_anschlag_1-1568x1140.jpg 1568w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><figcaption class=\"wp-element-caption\"> <em>Fig. 7: Air gap between the engine throttle lever and the limit screw<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n<h5 class=\"wp-block-heading h5-grey-background\">Adjusting the default values for the servo positions in the \u00bbactuator-setup\u00ab<\/h5>\n\n\n\n<p class=\"wp-block-paragraph\">The servo motor moves between the position where the generator is stopped (<strong>\u00bbstop position\u00ab<\/strong>) and the position where the generator operates under full load (<strong>\u00bbpos @full load\u00ab<\/strong>). Depending on the generator type, the standard values for the <strong>\u00bbstop position\u00ab<\/strong>, the <strong>\u00bbstart position\u00ab<\/strong>, the <strong>\u00bbpos @zero load\u00ab<\/strong> and the <strong>\u00bbpos @full load\u00ab<\/strong> are specified in the application software.  <\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Switch on the fpControl panel.<\/li>\n\n\n\n<li>Call up the service menu.<\/li>\n\n\n\n<li>Enter the service password.<\/li>\n\n\n\n<li>Select <strong>\u00bbactuator setup\u00ab<\/strong> in the service menu. <\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" width=\"130\" height=\"66\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/actuator_setup_menu_item.jpg\" alt=\"\" class=\"wp-image-5788\"\/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Check the value for the <strong>\u00bbstop position\u00ab<\/strong>, the value must <strong>always<\/strong> be <strong>\u00bb0\u00ab<\/strong>. Set to \u00bb0\u00ab if necessary.  Confirm with OK. <\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" width=\"130\" height=\"68\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/actuator_setup_stop_position.jpg\" alt=\"\" class=\"wp-image-5789\"\/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Check the value for the <strong>\u00bbstart position\u00ab.<\/strong> If the generator starts well, keep the default value, otherwise adjust the value by trial and error. Confirm with OK. <\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" width=\"130\" height=\"68\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/actuator_setup_start_position.jpg\" alt=\"\" class=\"wp-image-5790\"\/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Do not change the default value for the <strong>\u00bbpos @zero load\u00ab<\/strong>. Confirm with OK.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" width=\"130\" height=\"68\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/actuator_setup_zero_load.jpg\" alt=\"\" class=\"wp-image-5791\"\/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Adjust the value for <strong>\u00bbpos @full load\u00ab<\/strong> so that there is only an air gap between the <strong>engine throttle lever<\/strong> and the <strong>limit screw<\/strong> (compare with Fig. 7). <\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-table\"><table><tbody><tr><td><img decoding=\"async\" width=\"56\" height=\"56\" class=\"wp-image-2536\" style=\"width: 56px;\" alt=\"\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2019\/10\/information_sbu_transparent_52px.png\"><br><strong>Note:<\/strong> It is not the numerical value that is decisive here, but the position of the engine throttle lever in relation to the limit screw.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" width=\"130\" height=\"68\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/actuator_setup_full_load.jpg\" alt=\"\" class=\"wp-image-5792\"\/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Save settings and confirm with OK.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" width=\"128\" height=\"64\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/actuator_setup_save_settings.jpg\" alt=\"\" class=\"wp-image-5793\"\/><\/figure>\n\n\n\n<hr class=\"wp-block-separator has-css-opacity is-style-dots\"\/>\n\n\n\n<h3 class=\"wp-block-heading h3-weiss-blau\">Appendix<\/h3>\n\n\n\n<h5 class=\"wp-block-heading h5-grey-background\">Controls<\/h5>\n\n\n\n<table class=\"wp-block-table\"><tbody><tr><td><strong>Softkey<\/strong><\/td><td><strong>Function<\/strong><\/td><\/tr><tr><td><strong>&#8212;<\/strong><\/td><td>Decreases the current position &#8220;curr. pos.&#8221; by 500.<\/td><\/tr><tr><td><strong>&#8211;<\/strong><\/td><td>Decreases the current position &#8220;curr. pos.&#8221; by 50.<\/td><\/tr><tr><td><strong>+<\/strong><\/td><td>Increases the current position &#8220;curr. pos.&#8221; by 50.<\/td><\/tr><tr><td><strong>++<\/strong><\/td><td>Increases the current position &#8220;curr. pos.&#8221; by 500.<\/td><\/tr><tr><td><strong>ok<\/strong><\/td><td>Confirm the current value of &#8220;curr. pos.&#8221; and skip to the next page of the actuator setup. A changed value will be saved in the <a aria-label=\"EEPROM (opens in a new tab)\" href=\"https:\/\/knowledgebase.fischerpanda.de\/?page_id=3482\" target=\"_blank\" rel=\"noreferrer noopener\">EEPROM<\/a> in the step &#8220;Save settings?&#8221;.<\/td><\/tr><tr><td><strong>skip<\/strong><\/td><td>Skip to the next page of the actuator setup, changed values are <strong>NOT<\/strong> stored in the EEPROM.<\/td><\/tr><tr><td><strong>cancel<\/strong><\/td><td>Leave actuator setup, changed values are <strong>NOT<\/strong> stored in the EEPROM.<\/td><\/tr><\/tbody><\/table>\n\n\n\n<table class=\"wp-block-table\"><tbody><tr><td><strong>Hardkey<\/strong><\/td><td><strong>Function<\/strong><\/td><\/tr><tr><td><img decoding=\"async\" width=\"71\" height=\"71\" class=\"wp-image-3016\" style=\"width: 71px;\" alt=\"\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2019\/11\/fpControl-arrow-up-10mm.jpg\"><\/td><td>Use the panel\u2019s arrow-up key to move up through the softkeys on one side and to increase parameter values. A long press on the key activates the rapid increase of the parameter value.<\/td><\/tr><tr><td><img decoding=\"async\" width=\"71\" height=\"71\" class=\"wp-image-3015\" style=\"width: 71px;\" alt=\"\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2019\/11\/fpControl-arrow-down-10mm.jpg\"><\/td><td>Use the arrow-down key to move down through the softkeys on one side and to decrease parameter values. A long press on the key activates the rapid decrease of the parameter value.<\/td><\/tr><tr><td><img decoding=\"async\" width=\"71\" height=\"71\" class=\"wp-image-3014\" style=\"width: 71px;\" alt=\"\" src=\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2019\/11\/fpControl-start-stop-10mm.jpg\"><\/td><td>Use the start\/stop key to execute the action of a selected softkey and to confirm parameter values.<\/td><\/tr><\/tbody><\/table>\n\n\n\n<h5 class=\"wp-block-heading h5-grey-background\">Servo Parameter<\/h5>\n\n\n\n<table class=\"wp-block-table\"><tbody><tr><td><strong>stop position<\/strong><\/td><td>Position to which the servomotor moves to stop the generator.<\/td><\/tr><tr><td><strong>start position<\/strong><\/td><td>Position to which the servomotor moves when the generator is started.<\/td><\/tr><tr><td><strong>pos @zero load<\/strong><\/td><td>Position of the servomotor at idle.<\/td><\/tr><tr><td><strong>pos @full load<\/strong><\/td><td>Position of the servomotor at full load.<\/td><\/tr><tr><td><strong>Save settings?<\/strong><\/td><td>Saves the adjusted positions of the four previous pages in the EEPROM.<\/td><\/tr><\/tbody><\/table>\n\n\n\n<table class=\"wp-block-table\"><tbody><tr><td><strong>saved&nbsp;pos.<\/strong><\/td><td>Position value stored in EEPROM.<\/td><\/tr><tr><td><strong>curr.&nbsp;pos.<\/strong><\/td><td>Current value of the position, you can adjust this value live using the (+\/-) softkeys.<\/td><\/tr><tr><td><strong>RPM<\/strong><\/td><td>Current revolution speed of the diesel engine in [RPM]. If you adjust the position of the servo motor while the generator is running, you can directly observe the effect on the revolution speed.<\/td><\/tr><\/tbody><\/table>\n\n\n\n<hr class=\"wp-block-separator has-css-opacity is-style-dots\"\/>\n\n\n<div class=\"wp-block-post-date__modified-date wp-block-post-date\"><time datetime=\"2025-09-15T12:11:15+02:00\">September 15, 2025<\/time><\/div>","protected":false},"excerpt":{"rendered":"<p>You can adjust the minimum and maximum position of the servo motor on Fischer Panda generators with fpControl generator control and Kubota V1505 motor.<\/p>\n","protected":false},"author":2,"featured_media":0,"comment_status":"closed","ping_status":"closed","template":"","knowledgebase_cat":[163],"class_list":["post-7956","knowledgebase","type-knowledgebase","status-publish","hentry","knowledgebase_cat-vs-generator-system","entry"],"acf":[],"_links":{"self":[{"href":"https:\/\/knowledgebase.fischerpanda.de\/index.php?rest_route=\/wp\/v2\/knowledgebase\/7956","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/knowledgebase.fischerpanda.de\/index.php?rest_route=\/wp\/v2\/knowledgebase"}],"about":[{"href":"https:\/\/knowledgebase.fischerpanda.de\/index.php?rest_route=\/wp\/v2\/types\/knowledgebase"}],"author":[{"embeddable":true,"href":"https:\/\/knowledgebase.fischerpanda.de\/index.php?rest_route=\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/knowledgebase.fischerpanda.de\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=7956"}],"version-history":[{"count":10,"href":"https:\/\/knowledgebase.fischerpanda.de\/index.php?rest_route=\/wp\/v2\/knowledgebase\/7956\/revisions"}],"predecessor-version":[{"id":8069,"href":"https:\/\/knowledgebase.fischerpanda.de\/index.php?rest_route=\/wp\/v2\/knowledgebase\/7956\/revisions\/8069"}],"wp:attachment":[{"href":"https:\/\/knowledgebase.fischerpanda.de\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=7956"}],"wp:term":[{"taxonomy":"knowledgebase_cat","embeddable":true,"href":"https:\/\/knowledgebase.fischerpanda.de\/index.php?rest_route=%2Fwp%2Fv2%2Fknowledgebase_cat&post=7956"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}