You can adjust the minimum and maximum position of the servo motor on Fischer Panda generators with xControl generator control and Kubota V1505 motor. This is necessary, for example, when starting up for the first time and after changing a defective servo motor or a defective xControl generator control. <\/p>\n\n\n\n
Setting the minimum position<\/h3>\n\n\n\n
\n
Switch off the generator control.<\/li>\n\n\n\n
Mount the servo throttle lever on the servo motor so that the lever is horizontal (Fig. 1). <\/li>\n<\/ul>\n\n\n
\n
Fig. 1: Servo throttle mounted in horizontal position <\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
\n
Switch on the generator control. The servo throttle lever should now be in the approximately 4 o’clock position (Fig. 2). <\/li>\n<\/ul>\n\n\n
\n
Fig. 2: Servo throttle lever in 4 o’clock position<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
\n
Adjust the position of the engine throttle lever with the left nut (Fig. 3) so that there remains an air gap between the engine throttle lever and the stop lever (Fig. 4). <\/li>\n<\/ul>\n\n\n
\n
Fig. 3: Adjusting the position of the engine throttle lever with the left nut<\/em><\/figcaption><\/figure>\n<\/div>\n\n
\n
Fig. 4: Minimum position – air gap between engine throttle lever and stop lever<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
\n
Turn the right nut to the left as far as possible (Fig. 5) so that the engine throttle lever has no more clearance (Fig. 6). <\/li>\n<\/ul>\n\n\n
\n
Fig. 5: Turn the right nut left to the stop<\/em><\/figcaption><\/figure>\n<\/div>\n\n
\n
Fig. 6: No clearance between the right nut and the engine throttle<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n\n\n\n\n
Setting the maximum position<\/h3>\n\n\n\n
Calibration of the servo motor using the \u00bbACTUATOR-WIZARD\u00ab<\/h5>\n\n\n\n
\n
Switch on the xControl panel.<\/li>\n\n\n\n
Call up the service menu.<\/li>\n\n\n\n
Enter the service password.<\/li>\n\n\n\n
Select \u00bbactuator wizard\u00ab<\/strong> in the service menu. <\/li>\n<\/ul>\n\n\n\n
<\/figure>\n\n\n\n
\n
Run the \u00bbactuator wizard\u00ab<\/strong> to calibrate the servo motor. To do this, confirm the message \u00bbDrive actuator to position 0 now?\u00ab<\/strong> with the arrow-down key.<\/li>\n<\/ul>\n\n\n\n
<\/figure>\n\n\n\n
\n
Start the generator using the start\/stop key.<\/li>\n\n\n\n
Confirm the message \u00bbExecute now? (regulate on 270V!)\u00ab<\/strong> with the arrow-down key.<\/li>\n<\/ul>\n\n\n\n
<\/figure>\n\n\n\n
\n
After running the wizard, verify that in the full throttle position<\/strong> there is only an air gap between the engine throttle lever<\/strong> and the limit screw<\/strong> (Fig. 7). <\/li>\n<\/ul>\n\n\n
\n
Fig. 7: Air gap between the engine throttle lever and the limit screw<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
WARNING<\/strong><\/td><\/tr>
Electrical voltage<\/strong>. Danger to life<\/strong>. \u25ba Voltage measurement must only be carried out by qualified personnel.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n
\n
Measure the output voltage. The voltage must be 270 V<\/strong>. <\/li>\n<\/ul>\n\n\n\n
Note:<\/strong> If the output voltage after calibrating the servo motor with the \u00bbActuator wizard\u00ab<\/strong> is less than 270 V, the \u00bbActuator setup\u00ab<\/strong> must be used to set the maximum position<\/strong>.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n
Adjusting the default values for the servo positions in the \u00bbactuator-setup\u00ab<\/h5>\n\n\n\n
\n
Switch on the xControl panel.<\/li>\n\n\n\n
Call up the service menu.<\/li>\n\n\n\n
Enter the service password.<\/li>\n\n\n\n
Select \u00bbactuator setup\u00ab<\/strong> in the service menu. <\/li>\n<\/ul>\n\n\n\n
<\/figure>\n\n\n\n
\n
Set the value for the \u00bbmaximum position\u00ab<\/strong> so that there is only an air gap between the engine throttle lever<\/strong> and the limit screw<\/strong> (compare with Fig. 7). Confirm with OK. <\/li>\n<\/ul>\n\n\n\n
Note:<\/strong> It is not the numerical value that is decisive here, but the position of the engine throttle lever in relation to the limit screw.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n
<\/figure>\n\n\n\n
\n
Do not change the default value for the \u00bbminimum position\u00ab<\/strong>. Confirm the value with OK. <\/li>\n<\/ul>\n\n\n\n
<\/figure>\n\n\n\n
\n
Save settings and confirm with OK.<\/li>\n<\/ul>\n\n\n\n
<\/figure>\n\n\n\n\n\n\n\n
Appendix<\/h3>\n\n\n\n
Controls<\/h5>\n\n\n\n
Softkey<\/strong><\/td>
Function<\/strong><\/td><\/tr>
—<\/strong><\/td>
Decreases the current position “curr. pos.” by 500.<\/td><\/tr>
–<\/strong><\/td>
Decreases the current position “curr. pos.” by 50.<\/td><\/tr>
+<\/strong><\/td>
Increases the current position “curr. pos.” by 50.<\/td><\/tr>
++<\/strong><\/td>
Increases the current position “curr. pos.” by 500.<\/td><\/tr>
![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_1_min-pos_2.3_1-1024x575.jpg\")
![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_servo_gashebel_4Uhr_Pos_small.jpg\")
![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_4_max-pos_schraube_1-1024x745.jpg\")
![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_2_min-pos_anschlag_2-1024x576.jpg\")
![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_rechte_mutter_small.jpg\")
![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_rechte_mutter_anschlag_small.jpg\")
![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/actuator_wizard_menu_item.jpg\")
<\/figure>\n\n\n\n![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/actuator_wizard_start_page.jpg\")
<\/figure>\n\n\n\n![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/actuator_wizard_execute_now.jpg\")
<\/figure>\n\n\n\n![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/servo-einstellen-V1505_5_max-pos_anschlag_1-1024x745.jpg\")
![\"General](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2019\/04\/warning_r_general.gif\")
WARNING<\/strong><\/td><\/tr>![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2019\/10\/information_sbu_transparent_52px.png\")
![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/menu-actuator-setup.jpg\")
<\/figure>\n\n\n\n![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/max-pos.jpg\")
<\/figure>\n\n\n\n![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/min-pos.jpg\")
<\/figure>\n\n\n\n![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2022\/03\/save-settings.jpg\")
<\/figure>\n\n\n\n![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2019\/11\/fpControl-arrow-up-10mm.jpg\"){kind=icon}
<\/td>![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2019\/11\/fpControl-arrow-down-10mm.jpg\"){kind=icon}
<\/td>![\"\"](\"https:\/\/knowledgebase.fischerpanda.de\/wp-content\/uploads\/2019\/11\/fpControl-start-stop-10mm.jpg\")
<\/td>