Skip to content

Fischer Panda

Knowledge Base

  • Event Codes
    • Event Codes
    • iControl2 error codes
    • Inverter blink codes
  • fpControl View
  • fpControl
    • Application Notes fpC
    • Technical Datasheets fpC
    • Generator type codes
  • iControl2
    • Application Notes iC2
    • Technical Datasheets iC2
  • Inverter
    • Application Notes Inverter
    • Technical Datasheets Inverter
  • Communication
    • SAE J1939
    • NMEA 2000®
    • Victron GX
    • Multifunction Displays
  • System
  • Glossary
  • Service

Monthly Archives: October 2019

Event 46 – AGT B6 rail (-) low

The temperature of the bus rail “-” is below its lower limit.

Posted byFischer PandaOctober 28, 2019October 30, 2020Posted inEvent Codes

Event 47 – AGT B6 rail (+) low

The temperature of the bus rail “+” is under its lower limit.

Posted byFischer PandaOctober 28, 2019October 30, 2020Posted inEvent Codes

Event 45 – AGT B6 cooler low

The temperature of the B6 bridge and the temperature of the heatsink are below their lower limits.

Posted byFischer PandaOctober 28, 2019October 30, 2020Posted inEvent Codes

Event 150 – No generator type selected (iControl2 only)

The generator control is not configured. No generator type has been selected yet.

Posted byFischer PandaOctober 28, 2019October 30, 2020Posted inEvent Codes

Event 251 – Parameter changed in admin mode

A parameter has been changed in administration mode.

Posted byFischer PandaOctober 24, 2019October 30, 2020Posted inEvent Codes

iControl2 error codes

Translation of the iControl2 error codes, that are displayed on the iControl2 Panel, into the Fischer Panda J1939 event codes.

Posted byFischer PandaOctober 21, 2019October 30, 2020Posted iniControl2

RJ45 connector for Fischer Panda CAN-Bus

Contact numbers, assignments and wire colors of the RJ45 connector for the Fischer Panda CAN-Bus.

Posted byFischer PandaOctober 8, 2019October 30, 2020Posted inCommunication, SAE J1939

News

  • Event 172 – Synchronization Module offline December 18, 2020
  • Event 171 – Load Contactor switched off forced December 18, 2020
  • Start repetitions in automatic start mode November 26, 2020
  • Inverter blink codes November 13, 2020
  • Parallel connection of two asynchronous generators November 10, 2020

Categories

  • AGT
  • Application Notes fpC
  • Application Notes Inverter
  • Communication
  • Event Codes
  • fpControl
  • iControl2
  • Inverter
  • Multifunction Displays
  • NMEA 2000®
  • SAE J1939
  • Software Update
  • System
  • Technical Datasheets fpC
  • Technical Datasheets iC2
  • Technical Datasheets Inverter
  • Victron GX

Archive

  • December 2020
  • November 2020
  • October 2020
  • September 2020
  • August 2020
  • July 2020
  • June 2020
  • May 2020
  • April 2020
  • January 2020
  • December 2019
  • November 2019
  • October 2019
  • September 2019
  • July 2019
  • June 2019
  • May 2019
  • April 2019

Search …

Fischer Panda, Proudly powered by WordPress. Data Protection Policy
  • Site Terms & Conditions (Impressum)
  • Home
  • Glossary
  • Service