Skip to content

Fischer Panda

Knowledge Base

  • Event Codes
    • Event Codes
    • iControl2 error codes
    • Inverter blink codes
  • fpControl View
  • fpControl
    • Application Notes fpC
    • Technical Datasheets fpC
    • Generator type codes
  • iControl2
    • Application Notes iC2
    • Technical Datasheets iC2
  • Inverter
    • Application Notes Inverter
    • Technical Datasheets Inverter
  • Communication
    • SAE J1939
    • NMEA 2000®
    • Victron GX
    • Multifunction Displays
  • System
  • Glossary
  • Service

Monthly Archives: June 2019

Event 131 – CAN communication lost: Generator control has lost the panel

The communication between the panel and the generator control is interrupted. The generator control has lost the panel. The generator is stopped because no operation is possible.

Posted byFischer PandaJune 19, 2019October 30, 2020Posted inEvent Codes

Event 130 – CAN communication lost: Panel has lost the generator control

The communication between the panel and the controller is interrupted. Panel has lost the generator control.

Posted byFischer PandaJune 19, 2019October 30, 2020Posted inEvent Codes

Event 111 – AGT B6 rail (+) high

The temperature of the bus rail “+” is above its upper limit.

Posted byFischer PandaJune 19, 2019October 30, 2020Posted inEvent Codes

Event 110 – AGT B6 rail (-) high

The temperature of the bus rail “-” is above its upper limit.

Posted byFischer PandaJune 19, 2019October 30, 2020Posted inEvent Codes

Event 109 – AGT B6 cooler high

The temperature of the B6 bridge and the temperature of the heatsink are above their upper limits.

Posted byFischer PandaJune 19, 2019October 30, 2020Posted inEvent Codes

Event 164 – Inverter DC link overvoltage

The voltage of the DC link is above its upper limit.

Posted byFischer PandaJune 17, 2019October 30, 2020Posted inEvent Codes

Event 163 – Inverter DC link overload

The current of the DC link is above ist upper limit.

Posted byFischer PandaJune 17, 2019October 30, 2020Posted inEvent Codes

Event 148 – Error three-phase rotating field

Error three-phase rotating field.

Posted byFischer PandaJune 17, 2019October 30, 2020Posted inEvent Codes

Event 151 – Error “Watchdog”

The electronic control unit works with a so called watchdog timer which is an embedded timing device. If there is a malfunction the watchdog timer resets the control unit.

Posted byFischer PandaJune 17, 2019October 30, 2020Posted inEvent Codes

Event 141 – Synchronization mode deactivated

The synchronization mode is deactivated.

Posted byFischer PandaJune 17, 2019October 30, 2020Posted inEvent Codes

Posts navigation

1 2 3 … 7 Older posts

News

  • Event 172 – Synchronization Module offline December 18, 2020
  • Event 171 – Load Contactor switched off forced December 18, 2020
  • Start repetitions in automatic start mode November 26, 2020
  • Inverter blink codes November 13, 2020
  • Parallel connection of two asynchronous generators November 10, 2020

Categories

  • AGT
  • Application Notes fpC
  • Application Notes Inverter
  • Communication
  • Event Codes
  • fpControl
  • iControl2
  • Inverter
  • Multifunction Displays
  • NMEA 2000®
  • SAE J1939
  • Software Update
  • System
  • Technical Datasheets fpC
  • Technical Datasheets iC2
  • Technical Datasheets Inverter
  • Victron GX

Archive

  • December 2020
  • November 2020
  • October 2020
  • September 2020
  • August 2020
  • July 2020
  • June 2020
  • May 2020
  • April 2020
  • January 2020
  • December 2019
  • November 2019
  • October 2019
  • September 2019
  • July 2019
  • June 2019
  • May 2019
  • April 2019

Search …

Fischer Panda, Proudly powered by WordPress. Data Protection Policy
  • Site Terms & Conditions (Impressum)
  • Home
  • Glossary
  • Service