Skip to content

Fischer Panda

Knowledge Base

  • Event Codes
    • Event Codes
    • iControl2 error codes
    • Inverter blink codes
  • fpControl View
  • fpControl
    • Application Notes fpC
    • Technical Datasheets fpC
    • Generator type codes
  • iControl2
    • Application Notes iC2
    • Technical Datasheets iC2
  • Inverter
    • Application Notes Inverter
    • Technical Datasheets Inverter
  • Communication
    • SAE J1939
    • NMEA 2000®
    • Victron GX
    • Multifunction Displays
  • System
  • Glossary
  • Service

Monthly Archives: April 2019

Event 26 – Engine revolution (RPM) low

The engine revolution is below its lower limit.

Posted byFischer PandaApril 18, 2019October 30, 2020Posted inEvent Codes

Event 152 – Inverter temperature high L1

The temperature of the inverter phase L1 is above its upper limit.

Posted byFischer PandaApril 18, 2019October 30, 2020Posted inEvent Codes

Event 25 – Starter battery voltage low

The starter battery voltage is below its lower limit.

Posted byFischer PandaApril 17, 2019October 30, 2020Posted inEvent Codes

Event 104 – Universal output 2 (5A) high

The current of the universal output 2 (5A) has is above its upper limit.

Posted byFischer PandaApril 16, 2019October 30, 2020Posted inEvent Codes

Event 39 – Universal Output 1 (1A) low

At this digital output the voltage drop is monitored. The voltage drop between the universal output 1 (1A) and ground is below its lower limit.

Posted byFischer PandaApril 16, 2019October 30, 2020Posted inEvent Codes

Event 93 – Power contactor

Too high current at the output for the load contactor.

Posted byFischer PandaApril 16, 2019October 30, 2020Posted inEvent Codes

Event 80 – Fuel supply output high

The current of the output for the fuel valve/fuel pump/excitation DC alternator is above its upper limit.

Posted byFischer PandaApril 15, 2019October 30, 2020Posted inEvent Codes

Event 83 – Water Pump/Fan high

The current of the output for the water pump/fan is above its upper limit.

Posted byFischer PandaApril 15, 2019October 30, 2020Posted inEvent Codes

Event 102 – Output Inverter DC supply high

The current at the output for the DC supply voltage of the inverter is above its upper limit.

Posted byFischer PandaApril 15, 2019October 30, 2020Posted inEvent Codes

Event 78 – Glow plugs output high

The current at the output for the glow plugs is above its upper limit.

Posted byFischer PandaApril 15, 2019October 30, 2020Posted inEvent Codes

Posts navigation

1 2 3 Older posts

News

  • Event 172 – Synchronization Module offline December 18, 2020
  • Event 171 – Load Contactor switched off forced December 18, 2020
  • Start repetitions in automatic start mode November 26, 2020
  • Inverter blink codes November 13, 2020
  • Parallel connection of two asynchronous generators November 10, 2020

Categories

  • AGT
  • Application Notes fpC
  • Application Notes Inverter
  • Communication
  • Event Codes
  • fpControl
  • iControl2
  • Inverter
  • Multifunction Displays
  • NMEA 2000®
  • SAE J1939
  • Software Update
  • System
  • Technical Datasheets fpC
  • Technical Datasheets iC2
  • Technical Datasheets Inverter
  • Victron GX

Archive

  • December 2020
  • November 2020
  • October 2020
  • September 2020
  • August 2020
  • July 2020
  • June 2020
  • May 2020
  • April 2020
  • January 2020
  • December 2019
  • November 2019
  • October 2019
  • September 2019
  • July 2019
  • June 2019
  • May 2019
  • April 2019

Search …

Fischer Panda, Proudly powered by WordPress. Data Protection Policy
  • Site Terms & Conditions (Impressum)
  • Home
  • Glossary
  • Service